Veridia Educational Systems




Emotional CPR
 
 
 
 
 
 



Laser Light Vs L.E.D. Light

Description: http://www.superpulsedpractice.com/images/1X1.gif

Light emitting diodes (LED) are tiny light bulbs but which have become enhanced dramatically over the last few years due to new LED techology. Unlike ordinary incandescent bulbs, they do not have a filament inside so they last longer and they are much brighter. LED’s create light solely by the movement of electrons in a semiconductor material within the small vacuum bulb. LED’s produce bright light in various wavelengths and LED light offers an amazing ‘vehicle of light’ for pulsed patterning and digital signaling therapy. LED light has been used in animal health for years, due to the simple way that light can offer the necessary energy to provide healing without the risks of ambient light damage to the eyes. The healing for both types of light therapy, comes from the conversion of photons to electrons. Light from LED’s do not offer extreme tissue penetration compared to laser light, but they provide the opportunity for the light to become available to the body in a natural and powerful way, that is well beyond natural sunlight. The LED principle is based on compression or light density. Old incandescent lights provide little healing value, due to their lack of ‘frequency’ and inability to concentrate enough light into one place.  LED is available in very low voltage, and it comes in various ‘NM Lengths or frequencies: 

The theory of light compression is more about lumens (brightness) rather than coherence or penetration (laser). Lumen density  aka, compression, offers the ability for the light to transfer through the tissues in a way similar to trans-absorption, rather than being injected or ‘focused’ into a specific area of tissue. General illumination or light transfer has the capacity to open up the pathways of connection because all light be it a laser or an LED is the same in one aspect… it’s all based on a single thing--a photon.. and photons bring electrons when they enter the body. With  Low Level LED Therapy it offers an abundance of  photons all available for use in the body—lasers just have them all running parallel to each other. So what you get from a laser in concentration you make up for in abundance of photons. In fact, there is very minimal difference between a low level laser and LED therapy at low voltages. The benefit of the LED therapy, is the risk with lasers can damage eye tissues if they inadvertently reach the eye, or they can damage the tissues if they are too strong. In those cases strong lasers are known as ‘hot lasers’. But LED light therapy is a safe and effective alternative and it has the same semiconductor capacity to carry imbedded signals through a pulsed patterning system.


The first law in photochemistry (Grotthus-Draper Law), states that light once absorbed creates a molecular reaction. photochemistry can occur, it is well known that the surface of the skin can carry the information of light through the transdermal tissues, much light acupuncture points and through waterous tissues. Light signaling has been documented by touching a light to an acupuncture point and measuring changes in the meridian through muscle testing.

 

LLL Therapy Offers a Healing Stimulus.

Wavelengths and Impact of Penetration and Absorption.

Portions of these diode wavelengths are visible, from 600 up to approximately 780 or 820 nm. Humans have a declining ability to see light above approximately 820nm. Photon energy increases as the wavelength decreases; conversely, penetration through the skin increases as wavelength increases. Thus, certain conditions may benefit from lower wavelengths where most of the energy is absorbed at the surface, and other conditions may benefit more from higher wavelengths that permit deeper penetration. It follows that an ideal wavelength for treating most conditions would be in the midrange.    

 

 

Description: http://www.superpulsedpractice.com/images/1X1.gif

 

Description: http://www.superpulsedpractice.com/images/1X1.gif

Colors and materials

Conventional LEDs are made from a variety of inorganic semiconductor materials, the following table shows the available colors with wavelength range, voltage drop and material:

Color

Wavelength [nm]

Voltage [V]

Semiconductor material

Infrared

λ > 760

ΔV < 1.9

Gallium arsenide (GaAs)
Aluminium gallium arsenide (AlGaAs)

Red

610 < λ < 760

1.63 < ΔV < 2.03

Aluminium gallium arsenide (AlGaAs)
Gallium arsenide phosphide (GaAsP)
Aluminium gallium indium phosphide (AlGaInP)
Gallium(III) phosphide (GaP)

Orange

590 < λ < 610

2.03 < ΔV < 2.10

Gallium arsenide phosphide (GaAsP)
Aluminium gallium indium phosphide (AlGaInP)
Gallium(III) phosphide (GaP)

Yellow

570 < λ < 590

2.10 < ΔV < 2.18

Gallium arsenide phosphide (GaAsP)
Aluminium gallium indium phosphide (AlGaInP)
Gallium(III) phosphide (GaP)

Green

500 < λ < 570

1.9[47] < ΔV < 4.0

Indium gallium nitride (InGaN) / Gallium(III) nitride (GaN)
Gallium(III) phosphide (GaP)
Aluminium gallium indium phosphide (AlGaInP)
Aluminium gallium phosphide (AlGaP)

Blue

450 < λ < 500

2.48 < ΔV < 3.7

Zinc selenide (ZnSe)
Indium gallium nitride (InGaN)
Silicon carbide (SiC) as substrate
Silicon (Si) as substrate – (under development)

Violet

400 < λ < 450

2.76 < ΔV < 4.0

Indium gallium nitride (InGaN)

Purple

multiple types

2.48 < ΔV < 3.7

Dual blue/red LEDs,
blue with red phosphor,
or white with purple plastic

Ultraviolet

λ < 400

3.1 < ΔV < 4.4

Diamond (235 nm)
Boron nitride (215 nm)
Aluminium nitride (AlN) (210 nm)
Aluminium gallium nitride (AlGaN)
Aluminium gallium indium nitride (AlGaInN) – (down to 210 nm)

White

Broad spectrum

ΔV = 3.5

Blue/UV diode with yellow phosphor

 


    Join pep  



 
Copyright ©2011  VES Veridia Educational Systems - All Rights Reserved.